Search results

I just had a thought. Even if the scv was totally dead, it should still make fuel pressure. The scv is wide open with no power to it. If there was no fuel flow/pressure and the pump has an uninterrupted fuel supply, then it has to be a faulty pump vs an scv.

Glad you sorted it out. The troubleshooting suggests it's a circuit code, but it seems to be a performance code instead.

The firewall junction box is a water magnet, might want to check inside. The troubleshooting is quick to blame the ECU, but I've never had to replace one. In my experience it's always something else. Just an idea, you could run an overlay to the scv and see if that fixes it.

I wouldn't trust the troubleshooting 100%. Verify that you're on the right pins. I would load test the wiring vs. a continuity check. Multimeters lie. It's saying you're looking for a pulse wave of 0-12v. The SCV is pulse width modulated. Ideally you'd use an oscilloscope.

Coalminer is exactly right. I'd like to add that the low coolant level alarm is probably not related. There are plenty of reasons why the low coolant alarm can go off. Here are some examples. They are prone to leak at hose connections when it's cold. Especially the hose clamp on the coolant...

They are on the left side of the engine, top of the cylinder head, among the fuel lines. Two up front and two in the back.

It should, yes. That's the big mystery here. I would want confirmation that it's set a P0045 before committing to turbo replacement.

Awesome. 2015-later trucks have far fewer regen problems, thankfully this one was easy to sort out.

If it was driven for any period of time with no oil pressure you might want to check a few bearings while you're in there

Describe your problem in detail for us.

Sure thing. Curious, which port did you have jpro hooked to? To access the engine ECU you use the 16 pin connector.

You cannot access the engine ECU from the 9 pin. Use the 16 pin.

Find anything?

They are right about the ignition and key, there are no security system components. Super weird problem you have here. Do you have a gps or eld or anything like that wired up? Water in the firewall junction box can cause havoc. 2007s have bolt on covers, but water can still get in from...

Chances are good that the ECU isn't powering up, or there are communication errors. The Junction box on the firewall behind the air filter is prone to water intrusion. Might want to open that up, disconnect everything, and inspect for water or corrosion. Might want to check the CAN physical...

Is ENG ECU main 2 fuse in place and good? That's ECU memory, and when you key on the ECU grounds the Engine ECU main relay, providing power to the ecu and turning it on. Without this power source, the ECU won't do anything.

That's pretty interesting. With Jpro connected, can you go into the engine ecu and command things like the EGR, VNT, ITV? Can you view live data? Just for the hell of it, disconnect the pressure sensors on the air tanks and see if the cluster starts working correctly.

What scan tool are you using? With DXII, you can go into engine customization and change the soot amount. Change it to something like 2.3 and it'll put the DPR graph to three bars, which is when it will attempt an automatic regen. Then you can look at temps and stuff during a driving regen...

I'm assuming you're referring to P244B, which sets when the DPR graph reaches ten bars. Is it at ten bars? Did you pull this code out of the dash? The reason this set is there's a burner issue, or its cries for a manual regen were ignored. BCU codes cannot be read from the dash. There's a...

I haven't personally learned the patterns of ATC failure yet. So far it seems sort of random. There's a TSB on this, too (your dealership should know this. The TSB says "Got a P0421? Replace ATC".)The TSB lists all the hardware and gaskets and stuff they recommend replacing, but it's not...