Search results

Right on Leo, also look at Ruger revolvers and Kimbers. Kimber is a bit on the expensive side but they make a couple of nice .45 carry pieces. I carry a Ruger SP101 when I do carry. It is a 5 shot revolver in .357. Small, short barrel but a bit on the heavy side. It will do the job if needed...

We run a 450 MBE with a Eaton/Fuller 10sp auto-shift. The worst we have ever got was 7.5mpg. We were loaded VERY heavy with strong head winds. The best was 11.7!!! Running VERY light and at 57 mph. So it seems we should run empty and slow!!! Layoutshooter

Scott's Truck Repair in Toledo is good on them too. That is where I get all my work done when I am home. Layoutshooter

We stopped running it as soon as we heard the noise. We have all our work done at shops, I have NO mechcanical talent. I sure hope we did not blow up anything. Ours went out of warrenty in Jan. I would have NEVER bought this unit if I had to put one on. I bought a used truck and it was on it. It...

Well, at least we set a record with our PROHEAT. It worked fine for five whole weeks!!!! WOW!! Now it has developed a loud rattling noise. It sounds like bearings of some sort. Water pump or generator. What a piece of junk!!!! It is even too heavy to use as a boat anchor!!!! Considering that...

I agree, run for an owner for AT LEAST 6 months. We ran with one for 2 years before we bought our own truck. The lift gate is a must. Pays for itself fast. The reefer is a toss up. I am not sure if I would spec a reefer truck. Ours is but we bought it used and it came that way. I would also...

I served 3 years in the Army Security Agency. That unit no longer exsits I went to school at Ft. Devens MA. I stationed in Misawa Japan and Homestead FL. I also spent 17 years witht the National Security Agency. I spent 5 years at an overseas site and 2 years at another state side site. The rest...

I have seen the Onan's encased in diamond plate or plain aluminum boxes. There are vents all around to cool them. ICT is putting out thier own APU. I have not seen it. Any idea who made the sleeper? Layoutshooter

Good luck on that one. The owner that I drove for had his in the 3 times in the two years I was with him, for that same problem. It NEVER did work right. Layoutshooter

I have seen some Onan's covered that way. Was it on an expediter? Freightliner of Gorgia does the Onan like that. Layoutshooter

We NEVER leave the dock without all the correct paperwork. Shippers certification etc. We NEVER leave without the proper placards. It is not worth it. We have left a load sitting because they didnot have the right papers. It was a nice load and we could have used the money but after several...

I drive for FedEx and by in large the all mile rate is higher on hazmat than non-hazmat loads. There are hassles from time to time but I take them more often than not. They have been keeping me rolling the last couple of weeks. Layoutshooter

I found some low beam bulbs at a TA. $16.49 each. I bought them because I need them but what a rip off. I will have to research this and find a better price. Layoutshooter

Thanks Arkjarhead, I think that is what I was trying to ask. Math sucks!!! I would be rich if it were not for numbers. They have always held me back. LOL Layoutshooter

I am glad to hear that I am not the only one that learned this the hard way. Makes me feel better!! LOL!! I was able to get the drivers side in. I put the bulb in first then connected the wires. I was able to put the bulb into the passenger side but there is no way to connect the wires. The...

I had bought a full set of 9006's low and high beams but like a dummy I did not check them to see if they fit until I needed them. I thought I had planned ahead. Who knew there were to different shapped 9006 series bulbs. Guess I should have. Layoutshooter

That is exactly what the CPA has down for us. It just seems goofy to me. I guess it's my slow nature with numbers. I hate them!!! LOL. I guess I don't have to understand it if it keeps the IRS happy. All the numbers work so I guess we will keep it up. Thanks a million. Layoutshooter

They are 9006 series. That is what I typed but the computer put 4006 to make me look stupid. Not that I need any help. I guess I will look at a FL dealer, I was just hoping to get them at Wally World prices. Layoutshooter

I have a 2006 M2 business class. The book calls for 4006 series headlight bulbs. I took an old one out and it had 4006 on it. I bought a set of 4006 lights that said they fit all 4006 aplications, they do not fit. My old ones are straight at the conector and the new ones have a 90 degree angle...

You got it right now. Use your tools for what they are. Good luck and hang in there. Layoutshooter