Search results

Do regular automotive ones stand up in trucks (T300 if it matters) or do you need the OEM type ones?

Anyone know the number that says logging begins at 10001lbs? Either I'm missing it or its a myth - and I'm pretty sure its not the latter.

Can GMC Savanna ecm's be programed to limit top speed and will they display idle percentage or is this asking too much?

Are these engines any good on reliability and longevity? I was looking for a 5 or 6 year old diesel around $15K but a dealer has an 07 GMC cutaway, 21K miles - price reduced from $25.5K to $21.5K. Truck is for city use with short highway runs mixed in - I need around 40K miles per year for 3-5...

Well it looks like I may have to try driving this T300 before getting some lessons on shifting a 10 speed, there's only about 10 potential stops between the dealer and where I need to get it for an inspection and traffic should be minimal on a weekend. I know the procedure, 1 through 5 -...

Anyone know of a place that can do an Oil Analysis and not take weeks to get back the results? Ideally somewhere that can get it done in under a week after receipt. Thanks

Looked at a used T300 today, just looking for thoughts on it. Truck looks to be in nice shape, no body damage to truck or van, no significant rust (other than parts of the lift) and price looks to be pretty good. 2003 T300 Day Cab (ex Paclease) Cat 3126-250 187500 miles Eaton 10 spd 12/21K...

Came (south) through customs today, 3 easy shipments - 2 regular ones and 300 or so snowboards and apparently set off the portal's neutron sensor. So they send me through the secondary portal then on to xray, then inside while they use the hand held, (twice) and after numerous phone calls, and...

Anyone know where to find the EPA label on a 2003?

Went across on my way south to cancel a bond and there was a FECC Stoops Century class at the NB booth, I was gonna go say hi but alas they had no issues and were sent on their way. :)

Been trying to peek under cabs but this might be easier. Can a T300/370 be converted to air ride cab mounts? I assume they don't offer then from the factory but since its the same as the other B cabs, what about a retro fit?

Yesterday while on the hunt for a new donut shop I stumbled upon that Pete ST I've seen on the road now and then. The donut shop had closed its doors some time ago and I was just about to leave when I looked down the alley next to it and found this. Turns out its a 384, has what looks to be a...

Anyone have any experience with Isuzu NPR's? I'm wondering if the smaller (14.5K) ones are any good and what the lifespan of the 175hp diesels is. Looking at getting one from Ryder, strictly city use, they seem to be pretty clean, well taken care of, not abused and most have mileage figures...

I know the air card thing has been discussed many times but what is best if you spend a lot of time north of the 49th? Since I spend a good 6 hours a day there and anything more than around 200 yards north of the border puts you on a Canadian network I'm not really sure what's the best option...

It seems there is no set position for landing gear placement for and aft. Does it matter if they are set further forward near the (tandem) drives, further back or does it really matter?

Anyone have one of these things? Do they work good? Where can you get one online? I found the TT and trailer only models at a farm equipment shop but they don't list the straight truck one, nearest I could figure on price by subtracting the price of the trailer version from the TT version...

I guess if this one gets a flat they can send another truck to fix/tow it. 2008 Kenworth T-300 With " Super Singles " More Pictures Added ~ - Chassis - General - Chassis & Fuel - Tow411 - Message Board - Yuku

Is there a chart/table that lists single vehicle or straight truck (3 axle) maximum GVW by state or does someone know if WA state has something other than 34K + 12K = 46K. I came across something that seems to indicate there is a 40K cap however the bridge formula tables and RCW's mention...

OK, So I am trying to figure out roughly what P plates would run, called WA IRP office and they gave me roughly (pretty close it seems) figures for the base jurisdiction (WA) but could tell me nothing of what BC will charge, said to call BC. So I call them and was told I have to fill out an...

Does anyone have one for truck washing and if so is a hot water version worth the extra cost?