Recent content by Jordan

greasytshirt you're help is always incredible! Thank you for doing what you do. I'd love to send you money, or a shirt/hat from my biz if you're interested. You're shared knowledge on this site has saved me thousands over the past few years!

It's fixed. Just a little more googling and found another thread on here with similar symptoms: 2017 Hino 268 Starting Issue Power Relay #3. Inside passenger dash fuse panel. Top row. Third from right. Still don't know what is powered by this relay because I can't find a breakdown, but...

I have a 2012 268A. When you turn the key, it acts almost like a dead battery, except the radio, headlights all turn on and appear as full power. The dash lights will not turn on as normal. The park brake light on the dash turns on, but super faded, then gradually brightens, then after 20-30...

I need the wiring diagram from the fuse box, specifically the Cab+B fuse. I have a truck with what appears to be a "parasitic battery drain". It was drawing upwards of 1.5 amps, but jumps around a lot. The biggest culprit was the dash cam/gps. When I eliminate these, it drops down to about...

Re E E E eally?... Well, that makes a lot of sense. I just went with the option that said North America behind it...and did think it was odd it was listed as COE. I just assumed my bootleg software was slightly limited/missing :censoredsign:. Forgive my ignorance, as I'm not a mechanic and I'm brand...

Hmmm.... When you say "Go into BCU, through ECU", can you help me clarify? Because I'm still lost. On the left side of the screen, there are three options: (Engine, DCU, and VCS) Wait a sec...Do you mean on this screen, I should select the BCU option?, bc again, I don't see it there: I have...

Well. Good news - Replaced the NOX Sensor, cleared codes and truck is running great. The bad news, the sensor wasn't covered under warranty since something had rubbed/chafed the wires at the top of sensors where the wires go into it. (I have my guys carry boards/2x4's with them to protect...

2012 Hino 268A - Trying to monitor BCU (code P141F) - Burner Control Unit Vin: 5VPNJ8JV4C4S53377 Mileage - Approx 300K Short Question: How the hell do I access the BCU for a test to monitor its performance? (Using DX2) Screenshots below. CEL is on. Truck isn't performing passive regen (but...

Man, you guys on here are awesome and doing great things for people. I hope you get paid A LOT for the service you provide on here! Thank you.

I dropped it off last night, assuming this to be the case. Dealer estimated 5 days before getting the truck into the shop. Just a bummer with that kind of downtime over something so simple. I considered just paying the $ and swapping them myself to keep it rolling but I think there are a...

From what I'm reading in the workshop manual, it appears I just need to replace the NOX sensor 2. The truck is still under full warranty, so I believe this would be covered. The problem is the dealer is out at least 1 week for repair. I appreciate any advice you may have.

2017 Hino 268A - P20EE and P204F, and P2216 Vin 5PVNV8JV6H4S57071 Approx 65k miles Preface: I'm not a mechanic, and sometimes do dumb things... Truck is/was driving fine. Started passive regen while driver operating, then popped on the engine light. Driver still operated the truck the...

Spot on! Fixed the original issue! Except there is now and ABS light that I can't get to go away. There were a couple switches on valve on the rear of the crossmember which I disconnected first to check connections. I believe this caused the ABS light to come on, but I was messing with...

I'll check this today, however, I also made an assumption that may be wrong: - If I remove the brake pedal switch from the pedal housing and leave it hang, which wouldn't allow the switch to engage/disengage, I can run the truck like normal with no problems (except no brake lights, but the...

Will do! Thanks!